AADE DFD2 Instructions

Step One

Adderall online pharmacy
Modafinil online drugstore || Generic names of xanax || Buy modafinil in toronto

Step Two

Interfacing to the Receiver
Preparing the Cables || Setting the VFO Frequencies
Setting the 455 kHz Offset || Automatic Switching Setup
Connecting the Frequency Counter to the Receiver
Mounting the Counter on the Receiver
Checking the Readouts for the Bands

Circuit Information

Circuit Description/Input Circuit || Circuit Diagram

Eliminating Birdies from the Counter

AADE DFD2 Diagnosis

Please see this Picture for an illustration of some soldering tips. Use the smallest soldering tip you have. The soldering pads are small and a large tip will cause trouble. Be very careful with a large tip and check for solder bridges to ground.

For detail information on the theory and design of the frequency counter, check out Neil's article "A PIC-Based Digital Frequency Display", May 1997, QST, pp 36-38. Topics covered are Theory of Operation, Setting up the DFD, and Operating Tips.

For more detailed information on these counters, check out Neil's web site: http://www.aade.com

The instructions for the DFD2 that uses a 10 MHz or 16 MHz crystal for the oscillator are located at DFD2 10 & 16 MHz Instructions. After building the unit return here and start at Testing

If you are using the DFD2 with the 16 MHz crystal, please click here for new information on adjusting the crystal frequency.

If you have the 20 MHz TXCO module, which is currently being shipped with the kits, follow the instructions below.

AADE DFD2 w/TXCO Instructions

There a 3 general steps to complete assembly and packaging of the DFD2.

1. Choose the final installation method. The suggested location is on the bottom blank PCB board. If you are building a case for the receiver, it is suggested to move the counter at least 3" from the receiver boards to help prevent counter birdies getting into the receiver. The optional back lighted display is included with the kits that are purchased with the receiver.

2. Assembly of the printed circuit board (PCB) and display module.

3. Final testing and radio interfacing of the completed unit.

There is an optional aluminum enclosure available from AADE that includes a plastic bezel.

The DFD2 has inputs for 3 signals. The connections are soldered directly to the pads on the counter PCB with 50 ohm miniature coax. The BFO connection is not used with the receiver.

You may also wish to have an on/off switch. An on/off switch is recommended to eliminate the birdies the display generates for critical receiving conditions. A switch is not supplied with the kit.

Printed Circuit Board Assembly


Step 1 || Step 2 || Step 3 || Step 4 || Step 5 || Step 6 || Step 7 || Step 8

Begin the actual PCB assembly by sorting out the supplied components. A Parts List is included with the kits shipped with the receiver, including additional parts for automatic switching of the bands.

Assemble the PCB per the following illustrations:


Step 1

Check the back of the board to make sure the TXO has been pre-soldered to the PCB. Neil has been shipping all the new kits with the TXO already soldered to the board.


Step 2

The parts are mounted with the ground plane of the board facing up.

Mount the IC sockets and the display header. Note the notches on the sockets. They are pointed out with the yellow arrows in the above picture.

The long pins on the header are mounted up. Short pins go into the PCB.


Step 3

Install and solder all resistors and the six back to back diodes.

A yellow line has been placed on the diodes to show where the band should be placed.

Double check the bands on the diodes before soldering. The diodes are very difficult to remove and reinsert.


Step 4

Install and solder the 9 .1 mfd capacitors.


Clonazepam 2mg 180 $540.00 $3.00 $486.00
Clonazepam 2mg 30 pills US$ 170.00 US$ 5.67
Clonazepam 2mg 360 pills US$ 1,030.00 US$ 2.86
Clonazepam 2mg 60 $238.00 $3.97 $214.20



  1. Clonazepam Westernport
  2. Nashotah
  3. Büren
  4. Columbus
  5. Wittstock


Trimethoprim drug allergy (DMPD). In fact, the National Institutes of Health (NIH) found such a diagnosis based on urinalysis alone. But it wasn't until 2007 that the CDC started to focus on DMPD. And that's after it had already decided for some time that there wasn't a "true" case of the condition, according to CDC spokeswoman Cynthia Schuchat. "In Zopiclone 7.5 mg deutsch 2007, when the new criteria was released, that decision based on new information about the symptoms," she told New York Times. "There was no single medical reason that could trigger an allergy. Generic drug prices canada vs us But this time the new criteria are better evidence for how common it is in adults." That is something the Food Allergy Initiative, which was established in 1994 to assess allergies, would agree with. "This is an important step in the development of a national registry DMPD," wrote Dr. Elizabeth G. Boushey, the program's director, in New England Journal of Medicine. And while the new criteria are based upon objective criteria, they still allow for subjective judgement of when a reaction is present, which could be a problem. According to the Associated Press, a child who lives in home with no pets, allergies and to foods have been included in prior screening tests for the condition. But new criteria also exclude those who are allergic to pollen, pets or allergen-specific food products, including tree nuts, and also include a wide variety of other "allergies." While the new criteria will have greatest impact in identifying a large population of children who aren't yet diagnosed, the CDC is also working on a new form of test to help identify children with the disease. And this is the good news of it. In addition to the more stringent and objective assessment of symptoms as outlined above, it's also important to note that there's now an increase in awareness of the condition, according to an article by the Washington Post. "More than 100,000 parents have contacted the Centers about their child's allergic reactions over the past two decades, most of them because their kids have become sick from one of these foods, the paper said." This week, the FDA is expected to decide which foods, or what substances, will fall under the definition of "hypersensitivity," generic clonazepam cost which would then lead to tighter regulations around them in the food supply.

  1. generic version of clonazepam
  2. buy generic clonazepam online
  3. generic clonazepam online
  4. generic clonazepam 1mg
  5. generic brands for clonazepam
  6. generic of clonazepam


Generic clonazepam 1mg



Buy real tramadol online Buying 2mg xanax online Tramadol hydrochloride 200 mg tablet Diazepam for sale dublin Green generic valiums


  • Clonazepam in Okla.
  • Clonazepam in Grand rapids
  • Clonazepam in Alabama
  • Clonazepam in Nelson
  • Clonazepam in W.va.


Does trimethoprim have penicillin in it ? When is amoxicillin available under the brand name Tramadol? Do you know how to order and Comprar modafinil online españa make a home treatment kit (HTC Kit)? What is the difference between levamisole and diclofenac (also known as Cipro®)? What is in the C-IV? Where can I obtain a CDL in Canada? Where can I obtain a foreign CDL, Canadian Driver License, or an International Driving Permit? Which medical tests are covered by OHIP? What is OHIP's coverage for prescriptions (doxepin, doxycycline, cefapen, or ceftriaxone)? What medications have to be registered for prescription in the Canadian General Pharmacopoeia under Schedule M? What medicines are covered by the Homeopathic Pharmacopoeia under Schedule K? What if the medication costs more than $20? Is your insurance company paying for the costs of administering Cipro? Why does the Canadian generic clonazepam 1mg government cover my hospital bills (if they are covered by OHIP)? How to obtain a Canada Student Health Insurance Plan (CSHP) for yourself and your dependents How can I request information about new drugs and the Canadian Pharmaceutical Association How can I get my Canadian Health Insurance Card ( CHIP ) or Medicare card ) or Medicare card What are the rules about buying insurance in the United States? Which health insurance programs must I apply through before travel? Where do I fill out and send all the forms? What documentation is necessary to prove eligibility for foreign health insurance and which countries are covered? What are the eligibility requirements for Canadian National Health Insurance program? What about CHIP in the United States and other US programs? Can I register for Medicare in a foreign country when I travel to Canada? Can I get the United Nations Population Fund's Family Health Checkup Service? Is the International Narcotics Control Strategy (INCS/USA) of the United States available in Canada? When can I get my health insurance card in the United States? Which health insurance plans are available for Canadian workers or permanent residents who are U.S. citizens? Is Medicare available in the U.S.? How Diazepam for sale 10mg uk do I register for prescription drugs with the United States Pharmacopeia (USP)? If I am an employee and plan on travelling to Canada, which health insurance programs must I apply through? Which Canadian organizations offer health insurance during pregnancy and postpartum? Which health insurers offer international insurance? I am employed abroad. Can travel to Canada by car, airplane, cruise ship, etc.? I work in Canada and live abroad. Do these plans have any restrictions based on work status? What is the cost and how does travel insurance work if it is my partner? Can I sign up for health insurance with another company in Canada? What do the benefits include? Can I cancel coverage? What is the policy term? Can I choose my insurance carrier (insurer)? What types of travel insurance are offered? I have an existing health insurance plan in Canada. How can I switch to another company? I bought my own vacation for the winter. Can I buy international health insurance to get that and my Canadian health insurance paid simultaneously? How old am I to travel? What health insurance must I have in Order phentermine online mexico the UK and U.S. before I travel to Canada? Are the health insurance policies same or similar? What are the conditions? How are the rates calculated? What forms must I fill out? Do they require my signature? What happens if I want to leave the UK or America? Can I cancel insurance and return to the US? When should I start my claim? How big is the payment? it paid on a per claim basis or term? strongest generic clonazepam What if it is paid out of U.S. pocket or a U.K. account? Are there any restrictions based on employment? Do you know what is covered at age? Will there be a cap? Are any limits? Who pays? Do I have to take care of it in the USA or Canada before moving to Canada? Where can I go for a general health check up? Is there a waiting list? Are it free? How long is the waiting time? Is it insured and how much coverage do you offer? How does it work? do I pay? What is covered and will the U.S. Government provide a letter of recommendation from the Canadian Embassy or Consulate? What are the costs for any services? How are rates calculated?

Is generic alprazolam the same as xanax Buy modafinil online with mastercard


WilliamsportStrawn
WerdauUhingen
Willow ParkClonazepam Interlachen


  1. generic clonazepam vs brand
  2. canada drug center coupons
  3. generic clonazepam 1mg
  4. canada drug pharmacy coupon


Neurontin capsule strengths (see the USP for Deltas. The patient should follow a reduction schedule of 1 to 2 mg per day. See Patient Counseling Information (PCI), starting at the end of Part 2, for more information about using diuretics safely. Patient Counseling Information Inform the patient: About the significance of potassium (K) elevations. How to avoid hyperkalemia (hypokalemia). How to monitor K levels. About the risk of dialysis. Advise the patient to eat approximately 600 mg of potassium per day; if the patient cannot eat this amount, ask the patient to swallow potassium chloride tablets or take (for example, Potassium Citrate and Chloride or Citrate-Chloride Chloride) for 4 to 6 hours after meals. About potential kidney problems associated with potassium-sparing diuretics or renal insufficiency. Advise the patient to inform healthcare provider of any acute medical conditions, including generic version of clonazepam chronic liver disease, the use of nephrenal agents (for example, peptic ulcer disease, alcohol use) and the presence or absence of diabetes mellitus. The patient should be under care of a healthcare provider if he or she is taking potassium-sparing diuretics and experiencing a significant change in kidney function. Tell generic clonazepam brands patients not to change the dose of potassium-sparing diuretics without consulting their healthcare provider. The patient should be asked to discontinue potassium-sparing diuretics if he or she experiences any symptoms that may be due to potassium (for example, nausea or vomiting, fever, shortness of breath, confusion). Diuretics that cause increased potassium level or abnormal urine analysis without any clinical signs of hyperkalemia are not considered appropriate for use as nephrectomies. For patients who are not able to swallow the dosage amount, advice on how to safely swallow potassium-sparing diuretics is available here – potassium citrate or chloride (for example, Potassium Citrate and Chloride) Other Important Information for Patients Who Receive a Na + K Receptor Blockade Patients should be advised that in addition to the use of diuretics, in order to prevent hypokalemia, it is very important to avoid a severe potassium (K) deficit. Patients must be advised to seek medical care Best xanax generic brand if their blood potassium (K) level drops more than 5 mmol/L, or if an acute K reduction is detected, with lower than expected levels of serum potassium (K), as this may be evidence of a clinical change in the patient's condition. Caution should be used when potassium (K) supplementation is being considered in patients treated with diuretics for high blood pressure. It does seem that potassium supplementation of sodium-sparing diuretics should be initiated cautiously because it is difficult to predict accurately how the potassium changes in normal, diabetic state may or not be absorbed. When the patient has hypokalemia and is on sodium-sparing diuretics, he or she is encouraged to discontinue these Clonazepam 2mg 360 pills US$ 1,030.00 US$ 2.86 drugs. There is considerable uncertainty as to whether potassium supplementation will affect a negative potassium index or whether further clonazepam generic xanax supplementation will increase serum potassium (> 5 mmol/L) levels. Potassium should not be obtained by intravenous route in patients with diabetes who have been treated with diuretics or are receiving Na + K receptor blockade. Na + K receptor blockade will decrease the normal.
Generic Clonazepam For Sale
97-100 stars based on 632 reviews

Install the 78L05 voltage regulator, the 10 mfd electrolytic and the two 15 turn trimpots.

The positive side of the 10 mfd electrolytic is located in the hole located closest to the edge of the PCB. The negative side of the capacitor is marked on the part.

Mount the flat side of the 78L05 toward the IC sockets as shown in the picture above. Be sure to mount it down as far as it will go on the board. Don't leave it sticking up in the air.


Step 6

On the back side of the PCB install and solder the 10K contrast control, the 25K calibration control, and the two 2 pin headers.

The short pins on the 2 pin headers go into the PCB, long pins face up.


Step 7

Install the PIC16C71 and the 74HC153.

On the far left, the PIC16C71, an 18 pin part.

Next on the left, the 74HC153, a 16 pin part.

The three horizontal chips are the 74HC4046s. Do not install them now. They will be installed later during "Testing" and "Setting the VFO Frequencies".

Note the notch location in the picture above and double check after you have placed them in the sockets.


Step 8

Install the female header on the display module. Note that the header is installed on pins 1-14. Be sure that pin 15 and 16 are empty! See picture above.

When mounting the display module on the PCB, note that the 10 mfd capacitor may need to be tilted over.

Make sure the header is mounted straight up on the display module. See picture above.

Solder one pin on the header, then reheat to get it positioned straight. Recheck position, then solder all the pins.

Testing


____Carefully inspect all of your solder connections, the polarity of the diodes, voltage regulator, the electrolytic capacitor, and the notch of the IC’s.

____Adjust the contrast control fully counter-clockwise.

____Plug the display module into the PCB 14 pin header.

____Attach the power supply, 8 to 12VDC, or 9V battery leads, to the marked pads on the back of the board near the bottom. Be sure to observe polarity with the negative lead to the grounded pad. (Picture)

If you reverse the power connections, the 78L05 will smoke. Not to worry, after replacing the 78L05, the counter should work.

____You should see some frequency displayed. Adjust the contrast control for the desired effect.

Wiring the LED back-lit display

Picture

The back-lit module has a block of LEDs behind the LCD display. It is powered from pins 15 and 16 with pin 15 being plus and pin 16 being minus (usually ground). The voltage drop across the LEDs is 4VDC. The current can range from 20ma to 150ma. The dropping resistor required is R = (V-4)/I where I is the desired current and V is the supply voltage.

One method that works well is to power it from the 78L05 regulator on the DFD2 as follows:

____On top of the display module, solder an insulated jumper wire from pin 1 (ground) to pin 16 (or the top connection of the LED module on the right side).

____Solder a 33ohm 1/4 watt resistor from pin 2 (+5VDC) to pin 15 (or the bottom connection to the LED module on the right side). The display is about as bright as a car radio dial at night.

Picture

Interfacing to the Receiver


Setting the VFO Frequencies || Setting the 455 kHz Offset on the Counter
Connecting the Frequency Counter to the Receiver
Checking the Readouts for the Bands (Jumper Settings and BPF & CF Switching)

Preparing the cables and soldering to the Frequency Counter PCB

____Measure and cut two 16" pieces of 50 ohm Teflon cable.
____Strip the ends of both cables so they are both prepared to solder to the receiver and counter PCB.

How to Strip the Telfon Coax

____Solder the cable prepared for the VFO to the VFO input (middle set of pads) on the counter PCB.
____Solder the cable prepared for the Crystal Oscillator to the HFO input (bottom set of pads).

____The BFO input will not be used with the receiver. Do not install the 74HC4046 in the top socket.

Or use a small piece of bare wire and short the BFO input to ground (directly on the PCB) and solder the jumper (Not necessary if the chip is not installed).

Setting the VFO Frequencies

If you do not have a bench Frequency Counter and need to use the DFD2 to set the VFO frequencies, follow these instructions. If you are using a bench counter to set the VFO, jump to Setting the 455 kHz Offset

____Remove all the 74HC4046s from the counter PCB.

Or,

____Short together the center conductor and shield that will connect to the Crystal Oscillator.
____Short together the center conductor and shield that will connect to the VFO.

____Apply power to the frequency counter and set the coarse (top pot) and fine (bottom pot) adjustments to show zero frequency on the display. Turn the pots counter-clockwise to set to zero.

Sometimes the counter will show all squares and no digits. Disconnect and re-apply power and the digits should show. Also, turn the viewing angle of the display to make sure they are visible.

____Disconnect power to the display.
____Install a 74HC4046 in the middle socket. This will allow VFO energy to reach the counter. (Or remove the short on the VFO cable, leave the HFO cable shorted.)
____Attach the VFO cable from the frequency counter PCB (center pair of pads) to the "Freq Cntr" box at the output of the VFO oscillator.
____Turn on the power to the receiver and the Frequency Counter.

Be very careful of reverse polarity connections. A reverse polarity connection to the frequency counter will blow the voltage regulator (78LO5). Use a diode at the 12 Volt input to the Frequency Counter if you think you might make a mistake. Band side of the diode goes toward the board.

____The Frequency Counter will display the VFO frequency.
____Set the 2/8 ceramic trim pot (labeled 14.068) to its middle position. Line up the slot in the adjustment screw with the capacitor pins, with the rotor plate on the end with the arrow. The rotor plate is the part of the top with the metallic color.
____Spread or compress the VFO toroid coil to set the frequency as close to 14.068 as possible.

Note: All tuning to make the frequency reach 14.068 is done by modifying the turns on the toroid.

If the frequency is too low with the turns moderately spread apart (13 MHz to 13.5 MHz), remove one turn on the toroid.

If the frequency is too high, add a turn to the toroid. (This may require rewinding the toroid for a clean appearance, but having the frequency read too high, >15MHz, is unlikely.)

____Secure the VFO toroid by whatever means you have decided. Some options are a small plastic wrap, a 4-40 screw/nut and 3/16" rubber grommet (cut to fit into the center of the toroid), or pour wax from a candle (let wax cool before proceeding). Picture

____Re-adjust the 2/8 ceramic trim pot labeled "14.068" to 14.066 MHz (Gives some room at the low end of the band.)
____Set the receiver to 40 Meters. Bandpass switch to the 40/30 side and the Crystal Filter switch to the 40/20 side. One LED should be on next to the 10.545 relay.
____Adjust the yellow trimmer next to the 10.545 relay for a frequency between 10.540 MHz to 10.543 MHz. (Gives some room at the low end of the band.)
____Set the receiver to 20 Meters. Bandpass switch to the 20/17 side and the Crystal Filter switch to the 40/20 side. Two LEDs should be on.
____Adjust the yellow trimmer next to the 10.445 relay for a frequency between 10.440 MHz to 10.443 MHz. (Gives some room at the low end of the band.)

Setting the 455 kHz Offset on the Counter

____Remove the VFO input 74HC4046 IC (middle chip). All the 74HC4046 chips should be removed for this adjustment.

____Make sure the reading is 0 kHz. This is done by turning the trimpots all the way counter-clockwise.

____Turn the coarse pot (upper one) clockwise to 384 kHz.

____Turn the fine pot (lower one) clockwise to reach 455 kHz.

Automatic Switching

The offsets and the adding/subtracting are done at Pins 12 and 13 of the PIC16C71. Pins 12 and 13 are brought out to a four pin set on the back of the counter. The chip has 100K internal resistors that bias the pins to 5 volts.

Two of the pins are grounds and the offsets are normally set by using a jumper to ground the necessary pins. With this receiver, wires are soldered to the left side pins (looking at the back). The right side pins are grounds. The left side pins are labeled "upper jumper" and "lower jumper" in these instructions.

There are two ways to connect the Frequency Counter to the receiver to achieve automatic switching of the bands on the counter. One is by using a small interface unit that uses diodes and two NPN transistors that connect to the switches on Board 1 of the receiver.

The second one is by using a rotary switch. The easiest one to wire is a two section rotary, either one wafer with two sections or two wafers. A rotary switch with one wafer can be used but is a little more complex to wire.

The "AADE DFD2 Auto Switching" page shows all the options available. Choose one at this time and wire it to the counter.

Connecting the Frequency Counter to the Receiver

____Attach the VFO cable from the Frequency Counter (middle pair of pads) to the VFO oscillator output box labeled "Freq Cntr". Picture

Note: The "Frequency Counter" output between the VFO amplifiers will not be used to drive the Frequency Counter. This connection overdrives the Frequency Counter and causes birdies in the receiver.

____Attach the HFO cable from the Frequency Counter (bottom pair of pads) to the Crystal Oscillator output box labeled "Freq Cntr". Picture
____Install the middle and bottom 74HC4046s. Leave the top one empty. The top one is the BFO input and will not be used.

Mounting the Counter on the Receiver

Getting the birdies of the counter out of the receiver has been researched for many hours. Just recently an accidental discovery showed the best way to mount the frequency counter for minimum birdies into the receiver.

Almost all the noise from the counter comes from the LCD updating circuit and is radiated by the display bezel and the display itself. Normally one would think that using good grounding techniques would eliminate that noise.

However, when adjusting the counter frequencies one day, the display was insulated from ground and there was no display noise in the receiver! A ground loop with the display must make the noise float in the ground circuit of the receiver.

Therefore, when mounting the frequency counter, DO NOT ground the display, let it float! The only ground to the display should be at the back of the PIC PCB ground connection on the back of the counter.

Since the mounting holes for the frequency counter are in the display board, this presents some extra effort to mount the display without grounding it.


Tito Magluyan, AC5QC presented the following idea on mounting the frequency counter. Using the teflon screws was added on later.

Using teflon screws and nuts are the easiest way to insulate the display. Tito used 12-2-G house wiring to make the mounting hardware.

Turns out #12 solid copper wire scrapped from house wiring fits very nicely inside the mounting holes of the display. Cut a couple of small pieces, bend one end around to make a place to mount a screw, then bend the other end to go through the bottom mounting hole of the display.

Take a teflon screw and run it through the bottom of the board and secure with a nut. Mount the display with the #12 copper wire mounting holes, and then take a second nut to secure the display.

The picture below shows how it is done a lot easier than trying to explain the process:

Yellow arrows point to the #12 house wiring that is used to help mount the display. The #12 solid copper wire just fits inside the mounting holes of the display and are soldered to the display PCB.


In case teflon hardware is not available, a trip to the hardware store yielded some 1/8" nylon wire clamps found in the wiring section.

A slot is cut in the middle of the nylon clamp for the PCB board to slip into.

Cutting the middle of the nylon clamp with a razor blade can be dangerous as the nylon is very hard. I used a hack saw blade to make an initial cut in the middle of the clamp, then a razor blade was used to make the slot wide enough for the PCB board. A pair of pliers (or a pair of vice grips, or a small vice) is used to hold the nylon clamp.

Then a tie wrap (the smallest available, approximately 1/8" or smaller) is use to mount the nylon clamp to the display mounting holes.

Picture shows both sides with the modified nylon clamps. Hardware (4-40 screw and nut) is used to hole the clamp together for easier handling.

Picture shows the final product with the wire wraps cut.

Final mounting of the display.


The picture above shows a shield mounted around the counter. The shield is not grounded to the display.

A small shield should be put around the counter to eliminate the remaining noise. One that just covers the counter between the top of the display and the bottom board of the receiver pretty much leaves a clean receiver.

Single sided blank PCB shield material is added to the kit for this purpose. Tin snips prove to be the best way to cut this material. You can also scribe a line on both sides with a sharp razor blade or knife and break apart the pieces you need.